RedBoot> ip_address -l 192.168.1.35 -h 192.168.1.2 IP: 192.168.1.35/255.255.255.0, Gateway: 0.0.0.0 Default server: 192.168.1.2, DNS server IP: 0.0.0.0 RedBoot> load -r -v -b 0x00080000 -h 192.168.1.2 zImage Using default protocol (TFTP) - Raw file loaded 0x00080000-0x0038396c, assumed entry at 0x00080000 RedBoot> exec 0x00080000 Using base address 0x00080000 and length 0x00303970 Booting Linux on physical CPU 0x0 Linux version 5.19.0-rc5-00002-g6e00f829f72e-dirty (linus@fedora) (armeb-openwrt-linux-muslgnueabi-gcc.bin (OpenWrt GCC 11.3.0 r20017+1-eb7d2abbf06f) 11.3.0, GNU ld (GNU Binutils) 22 CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=000039ff CPU: VIVT data cache, VIVT instruction cache OF: fdt: Machine model: Netgear WG302 v1 Memory policy: Data cache writeback Zone ranges: Normal [mem 0x0000000000000000-0x0000000001ffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000000000-0x0000000001ffffff] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff] Built 1 zonelists, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS0,9600n8 root=/dev/nfs rw nfsroot=192.168.1.2:/var/lib/tftpboot/ixp4xx-root,tcp,v3 ip=dhcp Dentry cache hash table entries: 4096 (order: 2, 16384 bytes, linear) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 21804K/32768K available (7168K kernel code, 221K rwdata, 1520K rodata, 1024K init, 123K bss, 10964K reserved, 0K cma-reserved) SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 clocksource: OSTS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28669193401 ns sched_clock: 32 bits at 67MHz, resolution 15ns, wraps every 32212576760ns Switching to timer-based delay loop, resolution 15ns Calibrating delay loop (skipped), value calculated using timer frequency.. 133.33 BogoMIPS (lpj=666660) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU: Testing write buffer coherency: ok Setting up static identity map for 0x100000 - 0x10006c devtmpfs: initialized clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: -1, 3072 bytes, linear) NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered NET: Registered PF_ATMPVC protocol family NET: Registered PF_ATMSVC protocol family vgaarb: loaded clocksource: Switched to clocksource OSTS NET: Registered PF_INET protocol family IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) TCP: Hash tables configured (established 1024 bind 1024) UDP hash table entries: 256 (order: 0, 4096 bytes, linear) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 32 Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=13 bucket_order=0 squashfs: version 4.0 (2009/01/31) Phillip Lougher jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered intel-extbus c4000000.bus: expansion bus at 50000000 intel-extbus c4000000.bus: CS0 at 0x50000000, size 0x800000, config before: 0xbfff3c42 intel-extbus c4000000.bus: CS0 enabled intel,ixp4xx-eb-write-enable intel-extbus c4000000.bus: CS0 wrote 0xbfff3842 into CS config gpio gpiochip0: (IXP4XX_GPIO_CHIP): not an immutable chip, please consider fixing it! ixp4xx-gpio c8004000.gpio: IXP4 GPIO registered ixp4xx-pci c0000000.pci: host bridge /soc/pci@c0000000 ranges: ixp4xx-pci c0000000.pci: MEM 0x0048000000..0x004bffffff -> 0x0048000000 ixp4xx-pci c0000000.pci: IO 0x004c000000..0x004c00ffff -> 0x0000000000 ixp4xx-pci c0000000.pci: IB MEM 0x0000000000..0x0003ffffff -> 0x0000000000 ixp4xx-pci c0000000.pci: activate hammering errata ixp4xx-pci c0000000.pci: controller is in host mode ixp4xx-pci c0000000.pci: set PCI_BASE_ADDR_0 to 0x00000000 ixp4xx-pci c0000000.pci: set PCI_BASE_ADDR_1 to 0x01000000 ixp4xx-pci c0000000.pci: set PCI_BASE_ADDR_2 to 0x02000000 ixp4xx-pci c0000000.pci: set PCI_BASE_ADDR_3 to 0x03000000 ixp4xx-pci c0000000.pci: set PCI_BASE_ADDR_4 to 0x04000000 ixp4xx-pci c0000000.pci: set PCI_BASE_ADDR_5 to 0xfffffc01 ixp4xx-pci c0000000.pci: set TRDY limit to 0x80ff ixp4xx-pci c0000000.pci: initialized as master ixp4xx-pci c0000000.pci: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem 0x48000000-0x4bffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] pci 0000:00:02.0: [168c:0013] type 00 class 0x020000 pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x0000ffff] PCI: bus0: Fast back to back transfers enabled pci 0000:00:02.0: BAR 0: assigned [mem 0x48000000-0x4800ffff] ixp4xx-qmgr 60000000.queue-manager: IXP4xx Queue Manager initialized. NPE-A: reset: npe_debug_instr(): timeout ixp4xx-npe c8006000.npe: NPE0 at [mem 0xc8006000-0xc8006fff] does not reset ixp4xx-npe c8006000.npe: NPE1 at [mem 0xc8007000-0xc8007fff] registered ixp4xx-npe c8006000.npe: NPE2 at [mem 0xc8008000-0xc8008fff] registered Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled printk: console [ttyS0] disabled c8000000.serial: ttyS0 at MMIO 0xc8000003 (irq = 19, base_baud = 921600) is a XScale printk: console [ttyS0] enabled c8001000.serial: ttyS1 at MMIO 0xc8001003 (irq = 20, base_baud = 921600) is a XScale brd: module loaded loop: module loaded physmap-flash 50000000.flash: initialized Intel IXP4xx-specific physmap control physmap-flash 50000000.flash: physmap platform flash device: [mem 0x50000000-0x507fffff] 50000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x000017 Intel/Sharp Extended Query Table at 0x0031 Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled Searching for RedBoot partition table in 50000000.flash at offset 0x7e0000 5 RedBoot partitions found on MTD device 50000000.flash Creating 5 MTD partitions on "50000000.flash": 0x000000000000-0x000000060000 : "RedBoot" 0x000000060000-0x000000660000 : "ixp425" 0x0000007c0000-0x0000007c1000 : "RedBoot config" mtd: partition "RedBoot config" doesn't end on an erase/write block -- force read-only 0x0000007c1000-0x0000007c2000 : "Config backup" mtd: partition "Config backup" doesn't start on an erase/write block boundary -- force read-only 0x0000007e0000-0x000000800000 : "FIS directory" ixp4xx_eth c8009000.ethernet eth0: eth0: MII PHY 0 on NPE-B hdlc: HDLC support module revision 1.22 ath5k 0000:00:02.0: enabling device (0340 -> 0342) ath5k 0000:00:02.0: registered as 'phy0' ath5k: phy0: Atheros AR5212 chip found (MAC: 0x56, PHY: 0x41) ath5k: phy0: RF2112B 2GHz radio found (0x46) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver usbcore: registered new interface driver usb-storage i2c_dev: i2c /dev entries driver ixp4xx_crypto c8006000.npe:crypto: probing... NPE-C: firmware functionality 0x5, revision 0x2:1 platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 cfg80211: failed to load regulatory.db ixp4xx-watchdog ixp4xx-watchdog: IXP4xx watchdog available usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered PF_PACKET protocol family XScale DSP coprocessor detected. Loading compiled-in X.509 certificates NPE-B: firmware functionality 0x2, revision 0x2:1 ixp4xx_eth c8009000.ethernet eth0: eth0: link up, speed 100 Mb/s, full duplex Sending DHCP requests ., OK IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.149 IP-Config: Complete: device=eth0, hwaddr=12:29:b0:6a:28:44, ipaddr=192.168.1.149, mask=255.255.255.0, gw=192.168.1.1 host=192.168.1.149, domain=bredbandsbolaget se, nis-domain=(none) bootserver=0.0.0.0, rootserver=192.168.1.2, rootpath= nameserver0=192.168.1.1 cfg80211: Loading compiled-in X.509 certificates for regulatory database cfg80211: Loaded X.509 cert 'sforshee: 00b28ddVFS: Mounted root (nfs filesystem) on device 0:12. Freeing unused kernel image (initmem) memory: 1024K Run /sbin/init as init process init: Console is alive init: - watchdog - kmodloader: no module folders for kernel version 5.19.0-rc5-00002-g6e00f829f72e-dirinit: - preinit - random: crng init done Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level urandom-seed: Seed file not found (/etc/urandom.seed) procd: - early - procd: - watchdog - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. kmodloader: no module folders for kernel version 5.19.0-rc5-00002-g6e00f829f72e-dirurngd: v1.0.2 started. BusyBox v1.33.0 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r16563+1-1c4cd71109d1 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/# root@OpenWrt:/# root@OpenWrt:/# root@OpenWrt:/# root@OpenWrt:/# root@OpenWrt:/# root@OpenWrt:/# eth0: link down