found magic num found magic num found magic num bootLoader made time: 1238800322 bootLoader version: 2.00b08 bootloader model name : dns-313v3 Waiting for disk ready & detect ... IDE 0 Detect disk 0 Disk Drive: IDE-0, Device-0, 976773168 Sectors [UDMA6] 500 GB 139 MB Partition 1: Linux 2048 Sectors 1 MB Partition 2: Linux 4096 Sectors 2 MB Partition 3: Linux 57344 Sectors 29 MB Partition 4: Linux 976707632 Sectors 500 GB 106 MB foun file zImage Processor: SL3512c3 CPU Rate: 300000000 AHB Bus Clock:150MHz Ratio:2/1 MAC 1 Address: 14:D6:4D:A8:3C:4F MAC 2 Address: 00:50:C2:22:22:22 inet addr: 0.0.0.0/255.255.255.0 Kernel RAM Location: 0x00600000 Filename: /.boot/zImage Initrd RAM Location: 0x00800000 Filename: /.boot/ramdisk.bin.gz Andge Test Code 0.03 (DAS Mode LED) ... PHY 0 Addr 1 Vendor ID: 0x001cc912 ==> enter ^C to abort booting within 2 seconds ...... boot from ide made time: 1275491212 version: 2.01b04 Load rd.gz 110 ,fileSize is 110...made time: 1275491212 version: 2.01b04 Load zImage 2473502 ,fileSize is 2473502...made time: 1275491212 version: 2.01b04 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.19 (linus@linux.local) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r8862-360efb1eadeb)) #0 PREEMPT Mon Feb 4 20:56:31 2019 [ 0.000000] CPU: FA526 [66015261] revision 1 (ARMv4), cr=0000397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: D-Link DNS-313 1-Bay Network Storage Enclosure [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x02c00000 [ 0.000000] random: get_random_bytes called from start_kernel+0x70/0x434 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,19200n8 root=/dev/sda4 rw rootwait [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 41456K/65536K available (4849K kernel code, 183K rwdata, 1376K rodata, 184K init, 224K bss, 7696K reserved, 16384K cma-reserved, 0K high) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc4800000 - 0xff800000 ( 944 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (4850 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) ( 184 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 184 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 225 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: FTTMR010-TIMER2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.000025] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.000124] Switching to timer-based delay loop, resolution 40ns [ 0.000865] Console: colour dummy device 80x30 [ 0.001000] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.001066] pid_max: default: 32768 minimum: 301 [ 0.001825] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001925] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.003801] CPU: Testing write buffer coherency: ok [ 0.007616] Setting up static identity map for 0x81e0 - 0x8228 [ 0.008167] rcu: Hierarchical SRCU implementation. [ 0.025080] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025164] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.028974] pinctrl core: initialized pinctrl subsystem [ 0.035832] NET: Registered protocol family 16 [ 0.042909] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.055000] No ATAGs? [ 0.064260] pinctrl-gemini 40000000.syscon:pinctrl: detected 3512 chip variant [ 0.064342] pinctrl-gemini 40000000.syscon:pinctrl: GLOBAL MISC CTRL at boot: 0x83c22037 [ 0.064389] pinctrl-gemini 40000000.syscon:pinctrl: flash pin is set [ 0.065846] pinctrl-gemini 40000000.syscon:pinctrl: initialized Gemini pin control driver [ 0.215203] pl08xdmac 67000000.dma-controller: FTDMAC020 1.16 rel 1 [ 0.215266] pl08xdmac 67000000.dma-controller: FTDMAC020 4 channels, has built-in bridge, AHB0 and AHB1, supports linked lists [ 0.215573] pl08xdmac 67000000.dma-controller: initialized 4 virtual memcpy channels [ 0.217316] pl08xdmac 67000000.dma-controller: DMA: PL080 rev0 at 0x67000000 irq 27 [ 0.217747] Gemini SoC 3512 revision c3, set arbitration 00200030 [ 0.218660] vgaarb: loaded [ 0.219895] SCSI subsystem initialized [ 0.234167] i2c-gpio gpio-i2c: error trying to get descriptor: -2 [ 0.246119] clocksource: Switched to clocksource FTTMR010-TIMER2 [ 0.338693] NET: Registered protocol family 2 [ 0.341517] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.341659] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.341765] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.341849] TCP: Hash tables configured (established 1024 bind 1024) [ 0.342356] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.342476] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.343284] NET: Registered protocol family 1 [ 0.353113] Crashlog allocated RAM at address 0x3f00000 [ 0.354038] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.444492] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.444548] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.473076] io scheduler noop registered [ 0.473128] io scheduler deadline registered [ 0.474251] io scheduler cfq registered (default) [ 0.474308] io scheduler mq-deadline registered [ 0.474340] io scheduler kyber registered [ 0.481126] ftgpio010-gpio 4d000000.gpio: FTGPIO010 @(ptrval) registered [ 0.483156] ftgpio010-gpio 4e000000.gpio: FTGPIO010 @(ptrval) registered [ 0.485268] ftgpio010-gpio 4f000000.gpio: FTGPIO010 @(ptrval) registered [ 0.495258] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.504239] console [ttyS0] disabled [ 0.504517] 42000000.serial: ttyS0 at MMIO 0x42000000 (irq = 18, base_baud = 3000000) is a 16550A [ 3.553353] console [ttyS0] enabled [ 3.582494] gemini_sata_bridge 46000000.sata: SATA ID 00000e00, PHY ID: 01000100 [ 3.627683] gemini_sata_bridge 46000000.sata: set up the Gemini IDE/SATA nexus [ 3.672853] pata_ftide010 63000000.ata: set up Gemini PATA0 [ 3.707538] pata_ftide010 63000000.ata: device ID 00000500, irq 26, reg [mem 0x63000000-0x63000fff] [ 3.762505] pata_ftide010 63000000.ata: SATA0 (master) start [ 3.976229] gemini_sata_bridge 46000000.sata: SATA0 PHY ready [ 4.010755] pata_ftide010 63000000.ata: brought 1 bridges online [ 4.052797] scsi host0: pata_ftide010 [ 4.077788] ata1: SATA max UDMA/133 irq 26 [ 4.107916] of-flash 30000000.flash: no enabled pin control state [ 4.146543] of-flash 30000000.flash: no disabled pin control state [ 4.184061] of-flash 30000000.flash: initialized Gemini-specific physmap control [ 4.230158] Found: Eon EN29LV400AB [ 4.250753] 30000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank [ 4.289892] number of JEDEC chips: 1 [ 4.312119] ata1.00: ATA-8: SAMSUNG HD502HJ, 1AJ10001, max UDMA/133 [ 4.350697] Searching for RedBoot partition table in 30000000.flash at offset 0x70000 [ 4.397898] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 4.448064] No RedBoot partition table detected in 30000000.flash [ 4.485496] 3 fixed-partitions partitions found on MTD device 30000000.flash [ 4.529926] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD502HJ 0001 PQ: 0 ANSI: 5 [ 4.578608] Creating 3 MTD partitions on "30000000.flash": [ 4.611603] 0x000000000000-0x000000040000 : "RedBoot" [ 4.647779] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.701288] 0x000000040000-0x000000060000 : "MTD1" [ 4.731224] sd 0:0:0:0: [sda] Write Protect is off [ 4.765732] 0x000000060000-0x000000080000 : "MTD2" [ 4.796542] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.861086] libphy: GPIO Bitbanged MDIO: probed [ 4.894156] libphy: Fixed MDIO Bus: probed [ 4.938006] sda: sda1 sda2 sda3 sda4 [ 4.993314] gmac-gemini 60000000.ethernet: Ethernet device ID: 0x000, revision 0x1 [ 5.050238] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.079861] gemini-ethernet-port 60008000.ethernet-port: probe 60008000.ethernet-port ID 0 [ 5.131102] gemini-ethernet-port 60008000.ethernet-port: using a random ethernet address [ 5.183183] gemini-ethernet-port 60008000.ethernet-port eth0: irq 28, DMA @ 0x0x60008000, GMAC @ 0x0x6000a000 [ 5.244677] RTL8211B Gigabit Ethernet gpio-0:01: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=gpio-0:01, irq=POLL) [ 5.320112] gemini-ethernet-port 6000c000.ethernet-port: probe 6000c000.ethernet-port ID 1 [ 5.371378] gemini-ethernet-port 6000c000.ethernet-port: using a random ethernet address [ 5.423510] gemini-ethernet-port 6000c000.ethernet-port eth1: irq 29, DMA @ 0x0x6000c000, GMAC @ 0x0x6000e000 [ 5.483895] gemini-ethernet-port 6000c000.ethernet-port eth1: PHY init failed, deferring to ifup time [ 5.544021] rtc-ftrtc010 45000000.rtc: registered as rtc0 [ 5.579083] gemini-poweroff 4b000000.power-controller: Gemini poweroff driver registered [ 5.634617] gpio-fan gpio-fan: GPIO fan initialized [ 5.669883] ftwdt010-wdt 41000000.watchdog: FTWDT010 watchdog driver enabled [ 5.721384] NET: Registered protocol family 10 [ 5.753714] Segment Routing with IPv6 [ 5.777238] 8021q: 802.1Q VLAN Support v1.8 [ 5.819567] lm75 0-0048: hwmon1: sensor 'g751' [ 5.853549] i2c-gpio gpio-i2c: using lines 495 (SDA) and 496 (SCL) [ 5.891547] rtc-ftrtc010 45000000.rtc: setting system clock to 2018-05-14 21:06:08 UTC (1526331968) [ 5.974967] random: fast init done [ 6.489799] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) [ 6.535889] VFS: Mounted root (ext4 filesystem) on device 8:4. [ 6.572573] Freeing unused kernel memory: 184K [ 6.599298] This architecture does not have kernel memory protection. [ 6.637964] Run /sbin/init as init process [ 6.994062] init: Console is alive [ 7.015441] init: - watchdog - [ 7.336970] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 7.438615] usbcore: registered new interface driver usbfs [ 7.473303] usbcore: registered new interface driver hub [ 7.506798] usbcore: registered new device driver usb [ 7.717966] raid6: int32x1 gen() 18 MB/s [ 7.906529] raid6: int32x1 xor() 14 MB/s [ 8.097798] raid6: int32x2 gen() 29 MB/s [ 8.287026] raid6: int32x2 xor() 22 MB/s [ 8.477673] raid6: int32x4 gen() 39 MB/s [ 8.667056] raid6: int32x4 xor() 28 MB/s [ 8.856648] raid6: int32x8 gen() 40 MB/s [ 9.047348] raid6: int32x8 xor() 29 MB/s [ 9.073241] raid6: using algorithm int32x8 gen() 40 MB/s [ 9.105384] raid6: .... xor() 29 MB/s, rmw enabled [ 9.134389] raid6: using intx1 recovery algorithm [ 9.165643] xor: measuring software checksum speed [ 9.286535] arm4regs : 175.600 MB/sec [ 9.406494] 8regs : 165.600 MB/sec [ 9.526556] 32regs : 184.400 MB/sec [ 9.552009] xor: using function: 32regs (184.400 MB/sec) [ 9.771276] Btrfs loaded, crc32c=crc32c-generic [ 9.854207] fotg210_hcd: FOTG210 Host Controller (EHCI) Driver [ 9.915678] usbcore: registered new interface driver usb-storage [ 9.953506] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 10.008342] init: - preinit - [ 11.104720] random: jshn: uninitialized urandom read (4 bytes read) [ 11.218473] random: jshn: uninitialized urandom read (4 bytes read) [ 11.349863] gmac-gemini 60000000.ethernet: allocate 1024 pages for queue [ 11.407014] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 14.907799] mount_root: mounting /dev/root [ 14.935523] EXT4-fs (sda4): re-mounted. Opts: (null) [ 14.973909] urandom-seed: Seeding with /etc/urandom.seed [ 15.183589] procd: - early - [ 15.201703] procd: - watchdog - [ 16.212668] procd: - watchdog - [ 16.232908] procd: - ubus - [ 16.289836] random: ubusd: uninitialized urandom read (4 bytes read) [ 16.333352] random: ubusd: uninitialized urandom read (4 bytes read) [ 16.372927] random: ubusd: uninitialized urandom read (4 bytes read) [ 16.417658] procd: - init - Please press Enter to activate this console. [ 16.885279] kmodloader: loading kernel modules from /etc/modules.d/* [ 17.042215] async_tx: api initialized (async) [ 17.228236] RPC: Registered named UNIX socket transport module. [ 17.264261] RPC: Registered udp transport module. [ 17.292804] RPC: Registered tcp transport module. [ 17.321191] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 17.388276] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 17.546562] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 17.722835] usbcore: registered new interface driver ums-alauda [ 17.765734] usbcore: registered new interface driver ums-cypress [ 17.809789] usbcore: registered new interface driver ums-datafab [ 17.853566] usbcore: registered new interface driver ums-freecom [ 17.897475] usbcore: registered new interface driver ums-isd200 [ 17.941574] usbcore: registered new interface driver ums-jumpshot [ 17.985361] usbcore: registered new interface driver ums-karma [ 18.030077] usbcore: registered new interface driver ums-sddr09 [ 18.073790] usbcore: registered new interface driver ums-sddr55 [ 18.117924] usbcore: registered new interface driver ums-usbat [ 18.189160] xt_time: kernel timezone is -0000 [ 18.294683] PPP generic driver version 2.4.2 [ 18.329661] NET: Registered protocol family 24 [ 18.397279] kmodloader: done loading kernel modules from /etc/modules.d/* [ 20.527926] random: crng init done [ 20.548407] random: 5 urandom warning(s) missed due to ratelimiting [ 32.016385] br-lan: port 1(eth0) entered blocking state [ 32.076858] br-lan: port 1(eth0) entered disabled state [ 32.136062] device eth0 entered promiscuous mode [ 32.271202] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready BusyBox v1.30.0 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r9137+126-0465e41e0532 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#