COMMAND LINE DEFAULTS:  All command line options are toggles.  The C, X, S, 
D, P, Q, M, L, and F configuration options can be toggled on or off by the 
corresponding command line options, depending on the defaults chosen.  Most 
options are probably not desirable as defaults, but they're here just in 
case.

Option C -- Embedded Comments.  Some crunched files have a text comment 
embedded in their headers.  The vast majority of embedded comments are 
insignificant at best, so most people will not want to see them except when 
requested with the command line "C" option.  Nevertheless, if you want to 
see the comments by default choose "Yes" here.

Option X -- Alternate display.  If "Yes" is selected, two library member 
filenames will be displayed per line with their CRC's and indexes.  If "No" 
is selected, each line displays a single member with its date stamps, 
uncompressed name, and (optionally) its embedded comment.

Option D -- Date stamp preference.  LD normally looks first for a date 
stamp in the library's directory.  If no stamp is found there, it checks 
the headers of crunched files to see if there is an embedded date stamp.  
If "Yes" is selected here, LD will check for an embedded date stamp first 
and will use the directory stamp only if no embedded stamp is found or if 
the member file is not crunched.

Option S -- Summary only.  This option determines whether LD defaults to 
printing only the final summary line.  That can be quite useful, but 
probably not as the default.

Option P -- Screen paging.  If you want LD to pause each time the screen 
fills, set this option to "Yes".  If you're an Evelyn Wood alumnus, on the 
other hand, you might want to select "No" so continuous scrolling is the 
default.  With continuous scrolling you can still pause the screen with ^S 
or by using the command line "P" option.  (Screen paging is always off 
during printer output and quiet mode.)

Option Q -- Quiet mode.  This option determines whether LD will be in 
verbose or quiet mode by default.  (Yes, LD has a quiet mode!)  In quiet 
mode only error messages are displayed, which is sometimes useful with the 
M and L options, but nobody would want quiet mode as the default.  If 
you're nobody, select "Yes".

Option M -- Store results to memory.  LD can store the number of matching 
member files and the number of free library directory entries to message 
registers.  A "Yes" makes this the default; otherwise, the command line "M" 
option is required.

Option L -- Printer echo.  Printer (LST:) output is only allowed if the 
wheel byte is on.  Normally you won't want this as the default, but it's 
here just in case.

Option F -- Form feed printer.  LD can be configured to always send a form 
feed by default after a library directory is sent to the printer if "Yes" 
is selected.  A "No" means that a final form feed will only be output if 
the command line "F" option is used.

PERMANENT OPTIONS:  The following options are permanent configurations that 
cannot be changed from the command line.

Option R -- Message registers.  When storing the results to memory, LD uses 
four consecutive message registers.  The available registers are numbered 0 
to 31.  The register selected here will be the lowest one used, so the 
highest register number available is 28, which will use through register 
31.  Other programs (notably ZDE) use message registers, so make your 
selection based on register usage by other programs you commonly run.

Option D -- Date format.  The created and modified dates of libraries and 
their member files can be displayed in either "American" (mm/dd/yy) or 
"European" (dd.mm.yy) formats.  It's your choice.

Option T -- Time format.  The created and modified times of libraries and 
their member files can be displayed in either "Civilian" format (12-hour 
time, e.g., "3:21p") or "Military" format (24-hour time, e.g., "15:21"), 
whichever you prefer.

Option F -- Embedded date flag character.  The flag character selected here 
is printed between the date and time if it came from an embedded stamp in 
the header of a crunched file.  Any printable character can be selected, 
such as "-", "=", "*", "^", or "~".  If you do not want a flag displayed at 
all, enter a space character.

FOR NON-ZCPR3 SYSTEMS:  The following permanent options are ignored when 
running under ZCPR3.

Option S -- Number of screen lines.  Enter the number of lines on your 
screen.  You can enter any decimal number from 1 to 255.  This option is 
only for vanilla CP/M systems.  Under ZCPR3 the number of screen lines is 
obtained from the environment.

Option W -- Wheel byte address.  For vanilla CP/M remote systems that 
maintain a wheel byte, enter the address of that byte here as four 
hexadecimal characters.  If a wheel byte is not maintained, the address 
should be "0000".  Under ZCPR3 the address of the wheel byte is obtained 
from the environment.