; Title 'MEX overlay for the TRS-80 MOD IV version 1.7' ; Montezuma Micro CP/M 2.2 ; = = = = = = = = = = = = = = = = = = ; MEX TRS-80 MOD IV OVERLAY VERSION 1.0: Written 09/10/84 by Ed Richter ; ; VERSION 1.8 02/22/86 - Auto answer modified to work with the ; Model 4p internal modem command structure. ; Ignore all references to Hayes compatability. ; Bob Kitchen ; 73756,1015 ; VERSION 1.7 01/25/85 - ^C in "auto-answer" now aborts to CPM, not ; MEX (sorry bout that one). Added code to ; determine baud rate in "auto-answer". ; Changed "NITMOD" to default to the baud ; rate selected by "MSPEED" ; Ed Richter ; 71455,1133 ; VERSION 1.6 01/21/85 - A system reset seems a little drastic ; so added code for a ^C abort to auto ; answer. Also added "number of rings" ; equate. ; Ed Richter ; VERSION 1.5 11/17/84 - Added SET ANSWER ON command ; (For Hayes-compatible modems ; only...see NOTE below.) ; Thom Foulks ; VERSION 1.3 10/10/84 - Fixed bug in the Printer ready test ; Ed Richter ; VERSION 1.2 09/18/84 - Added the comments to 1.1 and changed the ; configuration of the SET message that is ; output to the console ; Ed Richter ; VERSION 1.1 09/16/84 - Added code to fully control the SIO USART ; via the SET command. This overlay now ; supports-- SET BAUD -- SET PARITY -- ; SET STOP BITS -- SET WORD LENGTH -- ; Ed Richter ; ; This file was derived from the MDM7xx overlay M7R4-5.ASM, and the ; file MXOPM10.ASM. It is a MEX overlay for use with the TRS-80 MOD ; IV, and an external modem. It has a SET command that supports 300 ; though 9600 baud. ; ; The SMARTMODEM, and compatibles will answer the phone at the ; incoming caller's baud rate. This makes it necessary to insure ; that the SIO-USART is configured to the same speed. This progam ; will answer the phone at the MSPEED baud rate. If it cannot ; read characters at that speed it will start at 110 baud (BAUD vector ; set to 0), check for a CR, LF, or ^C. If it is unable to read a ; character at that speed it will increment the baud rate to 1200 ; (the - CPI '6' - in the SKPBAUD routine), and retry at each step. ; To change the upper limit (1200) change the CPI '6' to the MSPEED ; value +1. ie., CPI '10' for 19200. ; ; NOTE: This overlay must be used in congunction with MXO-4P.ASM ; for full modem control. The SET ANSWER command will place MEX ; into an auto-answer mode which may be exited prior to execution ; with a ^C - CONTROL C - it's intended for use with a READ file ; similar to Bruce Morgen's WELCOME3 or WELCOME4. ; - Thom Foulks ; ; = = = = = = = = = = = = = = = = = REV: EQU 16 ; CR: EQU 0DH ;carriage return LF: EQU 0AH ;linefeed TPA: EQU 0100H TAB: EQU 09H YES: EQU 0FFH NO: EQU 0 RING: EQU '2' ;number of rings for auto-answer WMBOOT: EQU 05B39H ;MEX114.COM cpm stack pointer storage address ; ; ; Change the following information to match your equipment. ; PORT should be set to the base port address for the RS-232 port. ; PORT: EQU 0E8H ;master reset port MODCT1: EQU PORT+2 ;modem control port MODDAT: EQU PORT+3 ;modem data in port MODCT2: EQU PORT+2 ;not used mod iv BAUDRP: EQU PORT+1 ;baud rate port MDRCVB: EQU 080H ;bit to test for receive MDRCVR: EQU 080H ;value when ready MDSNDB: EQU 040H ;bit to test for send MDSNDR: EQU 040H ;value when ready ; MODCTB: EQU 0ECH ;dtr,rts,8,no,1 for port initialize CTSMSK: EQU 020H ;carrier detect mask ISOCD: EQU 0DFH ;port ready mask PRPORT: EQU 0F8H ;printer port PRSTAT: EQU 0C0H ;printer ready mask BRKMSK: EQU 0E3H ;send break DTRMSK: EQU 0EBH ;drop dtr ; ;MEX SERVICE PROCESSOR STUFF ; MEX: EQU 0D00H ;address of the service processor INMDM: EQU 255 ;get char from port,CY=no more in 100ms TIMER: EQU 254 ;delay 100 ms * reg b TMDINP: EQU 253 ;b=# secs to wait for char,CY=no char CHEKCC: EQU 252 ;check for ^C from kbd, Z=present SNDRDY: EQU 251 ;test for modem-send ready RCVRDY: EQU 250 ;test for modem-receive ready SNDCHR: EQU 249 ;send to modem (after SNDRDY) RCVCHR: EQU 248 ;recv a char from modem after (RCVRDY) LOOKUP: EQU 247 ;table search: see CMDTBL for info PARSFN: EQU 246 ;parse filename from input stream BDPARS: EQU 245 ;parse baud-rate from input stream SBLANK: EQU 244 ;scan input stream to next non-blank EVALA: EQU 243 ;evaluate numeric from input stream LKAHED: EQU 242 ;get nxt char w/o removing from input GNC: EQU 241 ;get char from input, CY=1 if none ILP: EQU 240 ;inline print DECOUT: EQU 239 ;decimal output PRBAUD: EQU 238 ;print baud rate CONOUT: EQU 2 ;simulated BDOS funct 2:CONSOLE OUT PRINT: EQU 9 ;simulated BDOS funct 9: PRINT STRING INBUF: EQU 10 ;input buffer, same as BDOS FUNCT 10 ; ORG 0D11H ;install printer ready test DW PRTSTS ; ORG TPA ; ; DS 3 ;(for "JMP START" instruction) PMODEM: DB NO ;Not used by MEX 103H SMODEM: DB NO ;Not used by MEX TPULSE: DB '*' ;Not used by MEX 105H CLOCK: DB 48 ;clock speed in MHz x10, 25.5 MHz max. 106H ;20=2 MHh, 37=3.68 MHz, 40=4 MHz, etc. MSPEED: DB 1 ;0=110 1=300 2=450 3=600 4=710 5=1200 107H ;6=2400 7=4800 8=9600 9=19200 default BYTDLY: DB 1 ;0=0 delay 1=10ms 5=50 ms - 9=90 ms 108H ;default time to send character in ter- ;minal mode file transfer for slow BBS. CRDLY: DB 1 ;0=0 delay 1=100 ms 5=500 ms - 9=900 ms 109H ;default time for extra wait after CRLF ;in terminal mode file transfer COLUMS: DB 5 ;number of DIR columns shown 10AH SETFL: DB YES ;yes=user-added Setup routine 10BH SCRTST: DB YES ;Cursor control routine 10CH DS 1 ;reserved (old ACKNAK flag) 10DH BAKFLG: DB YES ;yes=change any file same name to .BAK 10EH CRCDFL: DB YES ;yes=default to CRC checking 10FH TOGCRC: DB YES ;yes=allow toggling of CRC to Checksum 110H CVTBS: DB NO ;yes=convert backspace to rub 111H TOGLBK: DB YES ;yes=allow toggling of bksp to rub 112H ADDLF: DB NO ;no=no LF after CR to send file in 113H ;terminal mode (added by remote echo) TOGLF: DB YES ;yes=allow toggling of LF after CR 114H TRNLOG: DB YES ;yes=allow transmission of logon 115H ;write logon sequence at location LOGON SAVCCP: DB YES ;yes=do not overwrite CCP 116H LOCNXT: DB NO ;yes=local command if EXTCHR precedes 117H ;no=external command if EXTCHR precedes TOGLOC: DB YES ;yes=allow toggling of LOCONEXTCHR 118H LSTTST: DB YES ;yes=allow toggling of printer on/off 119H XOFTST: DB YES ;yes=checks for XOFF from remote while 11AH ;sending a file in terminal mode XONWT: DB NO ;yes=wait for XON after CR while 11BH ;sending a file in terminal mode TOGXOF: DB YES ;yes=allow toggling of XOFF checking 11CH IGNCTL: DB YES ;yes=CTL-chars above ^M not displayed 11DH EXTRA1: DB 0 ;for future expansion 11EH EXTRA2: DB 0 ;for future expansion 11FH BRKCHR: DB 'K'-40H ;^K = Send 300 ms. break tone 120H NOCONN: DB 'N'-40H ;^N = Disconnect from the phone line 121H LOGCHR: DB 'L'-40H ;^L = Send logon 122H LSTCHR: DB 'P'-40H ;^P = Toggle printer 123H UNSVCH: DB 'R'-40H ;^R = Close input text buffer 124H TRANCHR: DB 'T'-40H ;^T = Transmit file to remote 125H SAVECHR: DB 'Y'-40H ;^Y = Open input text buffer 126H EXTCHR: DB '^'-40h ;^^ = Send next character 127H DS 2 INCTL1: JMP STATSND ;go to "get status" 12AH DS 7 OTDATA: OUT MODDAT ! RET ;out modem data port 134H DS 7 INPORT: IN MODDAT ! RET ;in modem data port DS 7 MASKR: ANI MDRCVB ! RET ;bit to test for receive ready 148H TESTR: CPI MDRCVR ! RET ;value of rcv. bit when ready 14BH MASKS: ANI MDSNDB ! RET ;bit to test for send ready 14EH TESTS: CPI MDSNDR ! RET ;value of send bit when ready 151H DS 12 ;unused by MEX LOGON: DS 2 ;for user message 160H DIALV: DS 3 ;autodial rtn jump 162H DISCV: JMP DISCON ;disconnect rtn GOODBV: DS 3 ;not needed 168H INMODV: JMP NITMOD ;go to user written routine 16BH NEWBDV: JMP PBAUD ;set new baud-rate 16EH NOPARV: DS 3 ;(by-pass PMMI routine) 171H PARITV: DS 3 ;(by-pass PMMI routine) 174H SETUPV: JMP SETCMD ;initialize USART and modem 177H SPMENV: DS 3 ;not used with MEX 17AH VERSNV: JMP SYSVER ;print header msg 17DH BREAKV: JMP PBREAK ;send header 180H ; Do not change the following six lines. ILPRTV: DS 3 ; 183H INBUFV: DS 3 ; 186H ILCMPV: DS 3 ; 189H INMDMV: DS 3 ; 18CH NXSCRV: DS 3 ; 18FH TIMERV: DS 3 ; 192H ; ; Routine to clear to end of screen. If using CLREOS and CLRSCRN, set ; SCRNTEST to YES at 010AH (above). ; CLREOS: LXI D,EOSMSG ;clear to end of screen 195H MVI C,PRINT ;from cursor CALL MEX ; 198H RET ; 19DH ; CLS: LXI D,CLSMSG ;clear sreen 19EH MVI C,PRINT CALL MEX ; 1A1H RET ; 1A6H ; SYSVER: LXI D,SOMESG ;print the sys version msg 1A7H MVI C,PRINT CALL MEX CALL CRLF ; CARRSH LXI D,NOMESG ;no carrier present msg CALL CARRCK MVI C,PRINT CNZ MEX ;print if no carrier LXI D,CARMSG ;carrier present MVI C,PRINT CALL MEX ;say so and continue RET ; ; Send a break tone to reset some time-share computers. ; PBREAK: MVI A,BRKMSK ;send break OUT MODCT1 RET ; ; Routine to return status of the modem port ; STATSND: IN MODCT1 ;in modem contol port PUSH B ;just in case ANI ISOCD ;isolate status and clear CD bit MOV B,A ;save status IN PORT ;get CD bit ANI CTSMSK ;isolate CD bit ORA B ;merge CD with status POP B ;restore B RET ; ; This routine will hang up the phone by dropping DTR. ; DISCON: MVI A,DTRMSK ;DTR off, send BRK OUT MODCT1 ;send cmd MVI B,5 MVI C,TIMER CALL MEX ;delay 500 msec MVI A,MODCTB ;normal setup DTR on OUT MODCT1 RET ; ; This area sets the SIO-UART to an initial value of 8 bits, no parity, ; DTR on, and RTS on. ; NITMOD: MVI A,1 OUT PORT ;reset the USART to MVI A,MODCTB ;8,no,1,DTR, and RTS OUT MODCT1 LXI H,MSPEED MOV A,M ;initalize to MSPEED baud rate CALL PBAUD ;get baud rate RET ;also change the value of MSPEED ; ; Sets the modem speed via the SET COMMAND. ; SETCMD: MVI C,SBLANK ;any arguments CALL MEX JC SETSHO ;if not print out values LXI D,CMDTBL ;parse commands CALL TSRCH ;from table PUSH H ;address on stack RNC ;if yes then execute it POP H ;no fix stack SETERR: LXI D,SETEMS ;no then print error MVI C,PRINT CALL MEX RET CMDTBL: DB '?'+80H ;"set ?" DW STHELP DB 'BAU','D'+80H ;"set baud ?' DW STBAUD DB 'WOR','D'+80H ;set word length DW STWORD DB 'PARIT','Y'+80H ;set parity DW STPAR DB 'STO','P'+80H ;set stop bits DW STSTOP DB 'ANSWE','R'+80H ;set auto-answer on DW STANS DB 0 SETSHO: CALL CLS ;clear screen CALL CARRSH ;carrier present LXI H,SHOTBL ;show subroutines table SETSLP: MOV E,M ;get table address INX H MOV D,M INX H MOV A,D ;end of table ORA E RZ ;exit if yes PUSH H ;save table pointer XCHG ;addrs to HL CALL GOHL ;do it CALL CRLF ;print newline MVI C,CHEKCC ;check for console abort CALL MEX POP H ;its done JNZ SETSLP ;continue if no abort RET GOHL: PCHL SHOTBL: DW BDSHOW ;table DW PARSHOW DW WLSHOW DW STSHOW DW 0 STHELP: LXI D,HLPMSG ;print help message MVI C,PRINT CALL MEX RET STBAUD: MVI C,BDPARS ;MEX find baud rate CALL MEX JC SETERR ;none then exit CALL PBAUD ;valid baud rate then set it JC SETERR ;exit if not supported by overlay BDSHOW: CALL ILPRT DB 'Baud Rate:',TAB,' ',0 LDA MSPEED ;get MSPEED to determine present MVI C,PRBAUD ;baud rate CALL MEX RET STPAR: LXI D,PARTBL ;find parity function requested CALL TSRCH PUSH H RNC ;execute it POP H JMP SETERR ;not valid then say so STWORD: LXI D,WLTBL ;find word length function requested CALL TSRCH PUSH H RNC ;execute it POP H JMP SETERR ;not valid then say so STSTOP: LXI D,STTBL ;find how many stop bits CALL TSRCH PUSH H RNC ;execute it POP H JMP SETERR ;not valid then say so STANS: CALL CLS ;clear the screen PUSH H ;save H LXI H,ANSON ;get the set command CALL SMSEND ;send it POP H CALL CRLF ;get ready for msg CALL CRLF LXI D,ANSMSG ;and tell us about it MVI C,PRINT CALL MEX WAITCD: CALL INPORT ;to clear garbage CALL CARRCK ;check for carrier JZ TSTBAUD ;yes - go check baud rate... MVI C,CHEKCC ;no check for ^C CALL MEX JNZ WAITCD ;no carrier, no ^C so try again PUSH H ;save H LXI H,ANSOFF ;turn off auto answer at modem CALL SMSEND ;send it POP H LHLD WMBOOT ;^C -load CPM return address from ;stack pointer storage SPHL ;put it in the stack pointer RET ;and go to CPM TSTBAUD: CALL INPORT ;get byte from modem CPI CR ;if CR RZ ;baud rate is good go to MEX CPI LF ;if LF RZ ;baud rate is good go to MEX CPI 'C'-40H ;if ^C RZ ;baud rate is good go to MEX PUSH H PUSH B PUSH D LXI H,BAUD ;get baud rate start byte MOV A,M ;get it out of memory MOV C,A ;set it up to operate on it INR C ;add 1 to it MOV M,C ;and put it back in start byte CALL PBAUD ;go set baud rate and MSPEED CPI 6 ;have we tried 1200 baud JNZ TSTBAUD ;no then we're not done XRA A ;yes then get ready for retry STA BAUD ;by setting baud back to 110 POP D POP B POP H JMP WAITCD ;we didn't find a good baud rate ;so keep trying until - 1. get a ;good baud rate 2. get a ^C, or ;3. hangup causes carrier loss. ; HLPMSG: DB CR,LF,1AH,'SET command, TRS MOD 4 version 1.8',CR,LF DB CR,LF,'SET BAUD 300 1200 2400 4800 9600' DB CR,LF,'SET PARITY ON OFF ODD EVEN' DB CR,LF,'SET WORD 5 6 7 8' DB CR,LF,'SET STOP 1 2' DB CR,LF,'SET ANSWER ' DB CR,LF,LF,'Auto Answer configured for the Model 4p internal' DB ' modem only.',CR,LF DB CR,LF,'$' SETEMS: DB CR,LF,'SET command error',CR,LF,LF,'$' TSRCH: MVI C,LOOKUP JMP MEX ; ILPRT: MVI C,ILP ;MEX print function JMP MEX ; CRLF: MVI A,CR ;newline on console CALL TYPE MVI A,LF TYPE: PUSH H ;save em PUSH D PUSH B MOV E,A MVI C,CONOUT ;align output char CALL MEX ;print via mex POP B ;restore em POP D POP H RET ; ; Test for printer ready ; PRTSTS: IN PRPORT ;get printer status ANI PRSTAT ;isolate it JNZ PRTSTS1 ;return if not ready A=00 MVI A,0FFH ;ready A=FF RET PRTSTS1: XRA A RET ; Carrier detect 0=CARRIER ; CARRCK: IN PORT ;get carrier bit ANI CTSMSK RET ; ; Baud rate set routine ; PBAUD: PUSH H ;save everybody PUSH B PUSH D MOV E,A ;get speed MVI D,0 ;zero the other half of reg pair LXI H,BAUDTB ;get baud rate table address DAD D ;add speed offset MOV A,M ;get baud rate ORA A ;0=not valid baud rate JZ PBEXIT ;not valid baud rate then exit OUT BAUDRP ;good baud rate then set it MOV A,E ;get speed STA MSPEED ;set speed JMP PBEXIT1 ;return PBEXIT: STC PBEXIT1: POP B ;no carrier or incorrect baud rate POP D POP H RET ; BAUDTB: DB 0,055H,0,0,0 ;110,300,450,610,710 DB 077H,0AAH,0CCH,0EEH,0 ;1200,2400,4800,9600,19200 ; STTBL: DB '1'+80H ;stop bit tabe DW STONE ;set one bit DB '2'+80H DW STTWO ;set two bits DB 0 ; PARTBL: DB 'O','N'+80H ;parity table DW STON ;enable parity DB 'OF','F'+80H DW STOFF ;disable parity DB 'EVE','N'+80H DW STEVE ;even parity DB 'OD','D'+80H DW STODD ;odd parity DB 0 ; WLTBL: DB '5'+80H ;word length table DW STFIVE ;5 bit length DB '6'+80H DW STSIX ;6 bit length DB '7'+80H DW STSEV ;7 bit length DB '8'+80H DW STATE ;8 bit length DB 0 ; STFIVE: MVI A,MODCTB ;get current port info ANI 09FH ;change to 5 bits STA MODCTB ;put back new port info MVI A,'5' ;set 5 bit flag STFIVE1: STA WLTEL CALL CARRCK ;carrier present RZ ;yep then continue CALL TYPE ;position cursor CALL WLSHOW ;nope show word length RET STSIX: MVI A,MODCTB ;get current port info ORI 040H ;set six bits ANI 0DFH STA MODCTB ;put new MVI A,'6' ;set six bit flag JMP STFIVE1 STSEV: MVI A,MODCTB ;get current port info ORI 020H ;set seven bits ANI 0BFH STA MODCTB ;put back new port info MVI A,'7' ;set 7 bit flag JMP STFIVE1 STATE: MVI A,MODCTB ;get current port info ORI 060H ;set eight bit STA MODCTB ;put back new port info MVI A,'8' ;set 8 bit flag JMP STFIVE1 ; STON: MVI A,MODCTB ;get current port info ANI 0F7H ;set parity on STA MODCTB ;put back new port info MVI A,YES STON1: STA PARTEL ;set parity on flag CALL CARRCK ;carrier present RZ ;yep then continue CALL TYPE ;position cursor CALL PARSHOW ;nope then show parity info RET STOFF: MVI A,MODCTB ;get curent port info ORI 008H ;set parity off STA MODCTB ;put back new port info MVI A,NO ;set no parity flag JMP STON1 STODD: MVI A,MODCTB ;get current port info ANI 07FH ;set parity odd STA MODCTB ;put back new port info MVI A,YES ;set parity odd flag STODD1: STA PARTEL1 CALL CARRCK ;carrier present RZ ;yep then return CALL TYPE ;position cursor CALL PARSHOW ;nope show parity info RET STEVE: MVI A,MODCTB ;get current port info ORI 080H ;set even parity STA MODCTB ;put back new port info MVI A,NO ;set even parity flag JMP STODD1 STONE: MVI A,MODCTB ;get current port info ANI 0EFH ;set one stop bit STA MODCTB ;put back new port info MVI A,YES ;set one stop bit flag STONE1: STA STTEL CALL CARRCK ;carrier present RZ ;yep then continue CALL STSHOW ;nope show stop bit info RET STTWO: MVI A,MODCTB ;get current port info ORI 010H ;set two stop bits STA MODCTB ;put back new port info MVI A,NO ;set two stop bit flag JMP STONE1 ; PARSHOW: LXI D,PARMSG ;get parity message MVI C,PRINT ;print it CALL MEX LXI D,PONMSG ;get set for parity on MVI C,PRINT LDA PARTEL ;get flag CPI YES ;is it on JZ PARSHOW1 ;yes then say so LXI D,POFMSG ;no then get parity off message MVI C,PRINT ;print it CALL MEX RET PARSHOW1: CALL MEX LXI D,ODDMSG ;get parity odd message MVI C,PRINT LDA PARTEL1 ;get odd parity flag CPI YES ;is it odd JNZ PARSHOW2 ;nope get even message CALL MEX ;yes then say so RET PARSHOW2: LXI D,EVEMSG ;get even parity message MVI C,PRINT CALL MEX ;print it RET ; WLSHOW: LXI D,WLMSG ;get word length message MVI C,PRINT CALL MEX ;print it LXI D,FIVEMSG ;load five bit message MVI C,PRINT LDA WLTEL ;get word length flag CPI '5' ;is it five JNZ SIX ;nope try six CALL MEX ;yes then show it RET SIX: LXI D,SIXMSG ;load six bit message MVI C,PRINT CPI '6' ;is it six JNZ SEV ;nope try seven CALL MEX ;yep then show it RET SEV: LXI D,SEVMSG ;load seven bit message MVI C,PRINT CPI '7' ;is it seven JNZ ATE ;nope try eight CALL MEX ;yep then show it RET ATE: LXI D,ATEMSG ;load eight bit message MVI C,PRINT CALL MEX ;print it RET ; STSHOW: LXI D,STOPMSG ;get stop bit message MVI C,PRINT ;print it CALL MEX LXI D,STOPMSG1 ;get stop bit 1 message MVI C,PRINT LDA STTEL ;is it 1 bit CPI YES JNZ STSHOW1 ;nope try two CALL MEX ;yep then show it RET STSHOW1: LXI D,STOPMSG2 ;get stop bit 2 message MVI C,PRINT CALL MEX ;print it RET ; ; Message area ; BAUD: DB 0 ;300 baud PARTEL: DB NO ;yes=parity, no=no parity PARTEL1: DB YES ;yes=odd parity, no=even WLTEL: DB '8' ;5=5 bits,6=6 bits, etc. STTEL: DB YES ;yes=1 stop, no=2 stop STOPMSG: DB 'Number of stop bits is $' STOPMSG1: DB '1$' STOPMSG2: DB '2$' WLMSG: DB 'Word length is $' FIVEMSG: DB '5 bits$' SIXMSG: DB '6 bits$' SEVMSG: DB '7 bits$' ATEMSG: DB '8 bits$' PARMSG: DB 'Parity is: $' PONMSG: DB 'on and $' POFMSG: DB 'off$' ODDMSG: DB 'odd$' EVEMSG: DB 'even$' CLSMSG: DB CR,LF,1AH,'$' EOSMSG: DB CR,LF,19H,'$' SOMESG: DB 'TRS Mod 4 CP/M 2.2 overlay V' DB REV/10+'0' DB '.' DB REV MOD 10+'2','$' NOMESG: DB 'no $' CARMSG: DB 'carrier present',CR,LF,'$' ANSON: DB '*C*MAG@',125,'X',CR,0 ;turn on auto answer ANSOFF: DB '*C',CR,0 ;turn off auto answer ANSMSG: DB 'Modem answer mode now turned on. ' DB '[Use ^C to abort to CP/M]' DB CR,LF,'$' ; SMSEND: MVI C,SNDRDY CALL MEX JNZ SMSEND MOV A,M INX H ORA A RZ MOV B,A MVI C,SNDCHR CALL MEX JMP SMSEND ; ;---------------------------------------------------------------------- ; NOTE: MUST TERMINATE PRIOR TO 0B00H (with Smartmodem or Anchor) ;---------------------------------------------------------------------- ; End of TRS-80 MOD IV MEX modem overlay END