; B5CM-1.INS  -   BYE5 insert for Cermetek modems  -  07/17/85
;
;	   Cermetek Infomate 212A modem control package
;
; 	     Note:  This is an insert, not an overlay.
;
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
; 07/17/85  Renamed for use with BYE5		- Irv Hoff
; 12/14/84  Written for BYE3			- Paul Traina
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
;
; To use this code, the BYE5 routines for your USART must be modified:
;
;	IMODEM	EQU	YES	; Yes, using intelligent modem
;
;	After all USART and baud rate instructions have been executed
;	and IMMEDIATELY after DTR has been set logic true, (DTR must be
;	On for the Cermetek to receive and execute commands), add the
;	following:
;
;		 IF	IMODEM
;		CALL	IMINIT
;		 ENDIF
;
; The following hardware configuration is assumed:
; -----------------------------------------------
;	DTR (Pin 20) is supported
;	DCD (Pin 8) is supported
;	RI  (Pin 22) is NOT supported
;
; The following software configuration is assumed:
; -----------------------------------------------
;	CWAIT	EQU	20	; Wait up to 20 seconds for carrier
;	CLOSS	EQU	1	; If carrier lost wait 1 sec. to hang-up
;	NORING	EQU	YES	; Yes, UART ring indicator not available
;
; The following Infomate 212A default switches are assumed:
; --------------------------------------------------------
;	1=On   asynchronous mode
;	2=Off  8 data bits
;	3=Off  DCD active only when carrier is present
;	4=On   host controls DTR
;	5=On   battery backup enabled
;	6=Off  not using exclusion key phone
;	7=On   undocumented, should be on
;	8=Off  undocumented, should be off
;
; Notes:
; -----
;	The Cermetek will automatically set itself to the speed of the
;	calling modem, provided the speed is 300 or 1200 baud.	This
;	relieves us of the need to set the modem (still have to check
;	and set the USART/baud), via software instructions.
;
; Command strings sent to modem:
; -----------------------------
;	a. '  XY\r'
;		   Lets the modem "learn" what baud rate we're using.
;
;	b. The meaning of the second command string follows:
;	  '^NN ~'  Set command character to tilde ('~').
;	  '~P 04'  Do not echo commands, disconnect on loss of carrier
;	  '~U 1'   Tell modem to ignore commands when carrier present
;	  '~C 1'   Tell modem to answer phone after first ring
;
;	c. When the operator aborts BYE by typing a ^C when waiting for
;	   a call to come in, the modem should be sent a command string
;	   to reset it to a more "user-friendly" state, and also tell
;	   the modem to stop answering calls.  This third command string
;	   is as follows:
;	  '^NN ~'  Make sure tilde is command character
;	  '~C 0'   Disable auto-answer
;	  '~P 44'  Echo commands
;
;-----------------------------------------------------------------------
;
;
; Initialize the Infomate 212a.  DTR must be logic true for the modem to
; receive and process a command.
;
IMINIT:	CALL	IMLERN		; Make modem learn current baud rate
	DB	'  XY',CR
	DB	'  XY',CR,0
	CALL	IMSEND		; No delay - do not answer the phone
	DB	'N'-40H		; Send attention character
	DB	'N ~',CR	; Set new attention character
	DB	'~P 04',CR	; Disable command echo, enable carrier
	DB	'~U 1',CR	; Do not process command char if carrier
	DB	'~C 1',CR,0	; Answer phone after first ring
	RET
;.....
;
;
; Send string slowly for modem to find baud rate
;
IMLERN:	MVI	A,YES		; Set delay flag to yes
	STA	DLYFLG
	XTHL			; Save HL and get text address
	PUSH	B		; Save BC
	JMP	IMSEN1		; Continue with normal routine
;.....
;
;
; De-initialize the Cermetek.  DTR must be set logic true for modem to
; receive and process a command.  The ring register setting should be
; set to 0 so that the modem will not answer calls, also some other re-
; gisters should be reset, then after all is done, the USART routines
; should turn off DTR.
;
IMQUIT:	CALL	IMLERN		; Make modem learn baud rate
	DB	'  XY',CR
	DB	'  XY',CR,0
	CALL	IMSEND		; No delay - tell modem to shutdown
	DB	'N'-'@'		; Send attention character
	DB	'N ~',CR	; Set new attention character
	DB	'~P 44',CR	; Enable command echo
	DB	'~U 1',CR	; Do not process command char if carrier
	DB	'~C 0',CR,0	; Do not answer phone
	RET
;.....
;
;
; Send the Command String to the modem, similiar to how ILPRT sends to
; console.
;
IMSEND:	XRA	A		; Make sure there is no delay
	STA	DLYFLG
	XTHL			; Save HL and get address of message
	PUSH	B		; Save BC
;
IMSEN1:	CALL	MDOUTST		; Get the modem output status
	JZ	IMSEN1		; Not ready to send yet
	MOV	A,M		; If ready, get the character
	CALL	MDOUTP		; Send the character
	INX	H		; Point to next character
	CALL	DELAY		; Wait 100 ms here
	MOV	A,M		; Get next character
	ORA	A		; Are we all done?
	PUSH	PSW
	LDA	DLYFLG		; Check to see if we should delay
	ORA	A
	CNZ	DELAY		; If flag is set, delay another 100ms
	POP	PSW		; ..for a total of 200ms delay.
	JNZ	IMSEN1		; If not done, go do another
	POP	B		; Otherwise restore BC
	XTHL			; Restore HL and get return address
	RET
;.....
;
;
DLYFLG:	DB	0		; Delay flag
;
;			       end
;-----------------------------------------------------------------------