; M7EP-2.ASM -- Epson QX-10 overlay file for MDM7xx. 06/01/84 ; ; You will want to look this file over carefully. There are a number of ; options that you can use to configure the program to suit your taste. ; This file adapts the QX-10 computer to the modem program. Much of ; the information contained here is not in the MDM7xx.ASM file. ; ; Edit this file for your preferences then follow the "TO USE:" example ; shown below. ; ; Use the "SET" command to change the baudrate when desired. It starts ; out at 300 baud when the program is first called up. ; ; TO USE: First edit this file filling in answers for your own ; equipment. Then assemble with ASM.COM or equivalent ; assembler. Then use DDT to overlay the the results ; of this program to the original .COM file: ; ; ;============================================================================= ; ; SPECIAL NOTE: The MDMLNK.COM utility, if available to you, will ; overlay the .HEX file on the .COM file in one simple step. ; See MDMLNK instructions for further details. ; ;============================================================================= ; ; A>DDT MDM7xx.COM ; DDT VERS 2.2 ; NEXT PC ; 4A00 0100 ; -IM7EP-2.HEX (note the "I" command) ; -R ("R" loads in the .HEX file) ; NEXT PC ; 4A00 0000 ; -G0 (return to CP/M) ; A>SAVE 73 MDM7xx.COM (now have a modified .COM file) ; ; = = = = = = = = = = = = = = = = = = ; 06/01/84 - Slight changes for MDM740 - Robert Flagg ; 04/10/84 - Added parity, stop bit, word length - jw ; 11/11/83 - Renamed to M7EP-1.ASM, no changes - Irv Hoff ; 08/27/83 - Revised to work with MDM712 - Irv Hoff ; 07/25/83 - Changed M710XE.ASM forEpson QX-10 - Phil Becker ; ; = = = = = = = = = = = = = = = = = ; BELL: EQU 07H ;bell CR: EQU 0DH ;carriage return ESC: EQU 1BH ;escape LF: EQU 0AH ;linefeed ; YES: EQU 0FFH NO: EQU 0 TRUE EQU 0FFH FALSE EQU 0 ; BR7A: EQU 7AH BR7B: EQU 7BH BR4E: EQU 4EH BR4F: EQU 4FH ; PORT: EQU 11H ;Epson QX-10 serial output port MODCTL1: EQU PORT+2 ;Modem control port MODDATP: EQU PORT ;Modem data port MODCTL2: EQU PORT+2 ;Modem control port MODRCVB: EQU 01H ;Your bit to test for receive MODRCVR: EQU 01H ;Your value when receive ready MODSNDB: EQU 04H ;Your bit to test for send MODSNDR: EQU 04H ;Your value when send ready ; ; ORG 100H ; ; ; Change the clock speed as needed for your system. ; DS 3 ;(for "JMP START" instruction) ; PMMIMODEM: DB NO ;yes=PMMI S-100 Modem 103H AUTODIAL: DB NO ;yes=HAYES Smartmodem, no=non-Hayes 104H TOUCHPULSE: DB 'T' ;T=touch, P=pulse (Smartmodem-only) 105H CLOCK: DB 40 ;clock speed in MHz x10, 25.5 MHz max. 106H ;20=2 MHh, 37=3.68 MHz, 40=4 MHz, etc. MSPEED: DB 1 ;0=110 1=300 2=450 3=600 4=710 5=1200 107H ;6=2400 7=4800 8=9600 9=19200 default BYTDLY: DB 5 ;0=0 delay 1=10ms 5=50 ms - 9=90 ms 108H ;default time to send character in ter- ;minal mode file transfer for slow BBS. CRDLY: DB 5 ;0=0 delay 1=100 ms 5=500 ms - 9=900 ms 109H ;default time for extra wait after CRLF ;in terminal mode file transfer NOOFCOL: DB 5 ;number of DIR columns shown 10AH SETUPTST: DB YES ;yes=user-added Setup routine 10BH SCRNTEST: DB YES ;Cursor control routine 10CH RETRY: DB YES ;yes=reset the error limit to try again 10DH ;no=abort after 10 consecutive errors BAKUPBYTE: DB NO ;yes=change any file same name to .BAK 10EH CRCDFLT: DB YES ;yes=default to CRC checking 10FH TOGGLECRC: DB YES ;yes=allow toggling of CRC to Checksum 110H CONVRUB: DB YES ;yes=convert rub to backspace 111H TOGGLEBK: DB YES ;yes=allow toggling of rub to backspace 112H ADDLF: DB NO ;no=no LF after CR to send file in 113H ;terminal mode (added by remote echo) TOGGLELF: DB YES ;yes=allow toggling of LF after CR 114H TRANLOGON: DB YES ;yes=allow transmission of logon 115H ;write logon sequence at location LOGON SAVCCP: DB YES ;yes=do not overwrite CCP 116H LOCONEXTCHR: DB NO ;yes=local command if EXTCHR precedes 117H ;no=external command if EXTCHR precedes TOGGLELOC: DB YES ;yes=allow toggling of LOCONEXTCHR 118H LSTTST: DB YES ;yes=allow toggling of printer on/off 119H XOFFTST: DB YES ;yes=chcks for XOFF from remote while 11AH ;sending a file in terminal mode XONWAIT: DB NO ;yes=wait for XON after CR while 11BH ;sending a file in terminal mode TOGXOFF: DB YES ;yes=allow toggling of XOFF checking 11CH IGNORCTL: DB YES ;yes=CTL-chars above ^M not displayed 11DH EXTRA1: DB 0 ;for future expansion 11EH EXTRA2: DB 0 ;for future expansion 11FH BRKCHR: DB '@'-40H ;^@ = Send a 300 ms. break tone 120H NOCXNNCT: DB 'N'-40H ;^N = Disconnect from the phone line 121H LOGCHR: DB 'L'-40H ;^O = Send logon 122H LSTCHR: DB 'P'-40H ;^P = Toggle printer 123H UNSAVE: DB 'R'-40H ;^R = Close input text buffer 124H TRANCHR: DB 'T'-40H ;^T = Transmit file to remote 125H SAVECHR: DB 'Y'-40H ;^Y = Open input text buffer 126H EXTCHR: DB '^'-40H ;^^ = Send next character 127H ; ; DS 2 ; 128H ; IN$MODCTL1: MVI A,10H ;channel 0, reset interrupts. 12AH OUT MODCTL1 IN MODCTL1 ;get the status bits RET DS 3 ; OUT$MODDATP: OUT MODDATP ! RET ;out modem data port 134H DS 7 IN$MODDATP: IN MODDATP ! RET ;in modem data port 13EH DS 7 ANI$MODRCVB: ANI MODRCVB ! RET ;bit to test for receive ready 148H CPI$MODRCVR: CPI MODRCVR ! RET ;value of receive bit when rdy 14BH ANI$MODSNDB: ANI MODSNDB ! RET ;bit to test for send ready 14EH CPI$MODSNDR: CPI MODSNDR ! RET ;value of send bit when ready 151H DS 6 ; OUT$MODCTL1: OUT MODCTL1 ! RET ;out modem control port 15AH OUT$MODCTL2: OUT MODCTL2 ! RET ;out modem status port 15DH ; ; LOGONPTR: DW LOGON ;for user message. 160H DS 6 ; 162H JMP$GOODBYE: JMP GOODBYE ; 168H JMP$INITMOD: JMP INITMOD ;go to user written routine 16BH RET ! NOP ! NOP ;(by-passes PMMI routine) 66EH RET ! NOP ! NOP ;(by-passes PMMI routine) 171H RET ! NOP ! NOP ;(by-passes PMMI routine) 174H JMP$SETUPR: JMP SETUPR ; 177H JMP$SPCLMENU: JMP SPCLMENU ; 17AH JMP$SYSVER: JMP SYSVER ; 17DH JMP$BREAK: JMP SENDBRK ; 180H ; ; ; Do not change the following six lines. ; JMP$ILPRT: DS 3 ; 183H JMP$INBUF DS 3 ; 186H JMP$INLNCOMP: DS 3 ; 189H JMP$INMODEM DS 3 ; 18CH JMP$NXTSCRN: DS 3 ; 18FH JMP$TIMER: DS 3 ; 192H ; ; ; Clear sequences -- CLREOS is clear to end of screen, CLRSCRN is clear ; entire screen. Last entry must be 0. Any other 0's act as NOP's. ; CLREOS: CALL JMP$ILPRT ; 195H DB 017H,0,0,0,0 ; 198H RET ; 19DH ; CLRSCRN: CALL JMP$ILPRT ; 19EH DB 01AH,0,0,0,0 ; 1A1H RET ; 1A6H ; ; SYSVER: CALL CLRSCRN CALL JMP$ILPRT ; 1A7H DB 1BH,29H,'VERSION FOR EPSON QX-10',1BH,28H DB CR,LF,0 RET ;..... ; ; ;----------------------------------------------------------------------- ; ; NOTE: You can change the SYSVER message to be longer or shorter. The ; end of your last routine should terminate by 0380H (473 bytes ; available after start of SYSVER) if using the Hayes Smartmodem ; or by address 0B80H (2521 bytes) otherwise. ; ;----------------------------------------------------------------------- ; ; You can put in a message at this location which can be called up with ; CTL-O if TRANLOGON has been set YES. You can put in several lines if ; desired. End with a 0. ; LOGON: DB 'Hello from an Epson QX-10 user.',CR,LF,0 ;..... ; ; ; This routine allows a 300 ms. break tone to be sent to reset some ; time-share computers. ; SENDBRK: MVI A,5 OUT MODCTL1 MVI A,0F8H ;SEND A BREAK TONE JMP GOODBYE1 ;..... ; ; ; This routine sends a 300 ms. break tone and sets DTR low for the same ; length of time to disconnect some modems such as the Bell 212A, etc. ; GOODBYE: MVI A,5 OUT MODCTL1 ;SEND TO THE STATUS PORT MVI A,68H ;TURN OFF DTR, SEND BREAK ; GOODBYE1: OUT MODCTL1 MVI B,3 ;DELAY 300 MS. CALL JMP$TIMER MVI A,5 OUT MODCTL1 MVI A,0E8H ;RESTORE TO NORMAL, 8 BITS, DTR ON, ETC. OUT MODCTL1 RET ;..... ; ; ; Epson QX-10 initialization -- sets CTC timer 00H for send and receive ; baudrate. ; ; INITMOD: MVI A,1 STA MSPEED MVI A,0B6H OUT 7 MVI A,068H OUT 6 MVI A,000H OUT 6 CALL SETUP7201 INITMOD1: MVI A,BR4F RET ;..... ; ; SETUPR: CALL JMP$ILPRT DB CR,LF,'Baud Rate = ',0 CALL SETUPD CALL JMP$ILPRT DB CR,LF,LF,0 CALL JMP$ILPRT DB CR,'Input New Baud Rate (1=300, 2=1200): ',0 MVI C,1 CALL 5 CPI 31H JZ OK3 CPI 32H JZ OK12 CPI 0DH JZ OKBAUD JMP SETUPR ;TRY AGAIN ; OK3: MVI A,1 ;SET UP SPEED COMMAND STA MSPEED ;STORE SPEED MVI A,0B6H OUT 7 MVI A,0A0H OUT 6 MVI A,1 OUT 6 JMP SETUPF ;GO TO FORMAT SETUP ; OK12: MVI A,5 ;SET UP SPEED COMMAND STA MSPEED ;STORE SPEED MVI A,0B6H OUT 7 MVI A,068H OUT 6 MVI A,0 OUT 6 ; SETUPF: CALL JMP$ILPRT DB CR,LF DB 'Input Format (1=8N1, 2=7E1): ',0 MVI C,1 CALL 5 CPI 31H JZ OK8N1 CPI 32H JZ OK7E1 JMP SETUPF ;TRY AGAIN ; OK7E1: MVI A,3 STA PARITYBITS MVI A,040H STA DATABITS LDA MSPEED CPI 5 JZ OK7E1H MVI A,BR7B JMP SETUPDN OK7E1H: MVI A,BR7A JMP SETUPDN ; OK8N1: MVI A,0 STA PARITYBITS MVI A,0C0H STA DATABITS LDA MSPEED CPI 5 JZ OK8N1H MVI A,BR4F JMP SETUPDN OK8N1H: MVI A,BR4E ; SETUPDN: STA INITMOD1+1 SETUP7201: MVI A,4 OUT 013H LDA PARITYBITS MOV B,A LDA STOPBITS ORA B MOV B,A MVI A,040H ORA B OUT 013H MVI A,3 OUT 013H LDA DATABITS ORI 1 OUT 013H MVI A,5 OUT 013H LDA DATABITS RRC ORI 08AH OUT 013H JMP OKBAUD PARITYBITS: DB 0 STOPBITS: DB 4 DATABITS: DB 0C0H OKBAUD: CALL JMP$ILPRT DB CR,LF,0 RET ; SETUPD: LDA INITMOD1+1 CPI BR7A JNZ OK7B CALL JMP$ILPRT DB '1200 Baud - 7E1',0 RET OK7B: CPI BR7B JNZ OK4E CALL JMP$ILPRT DB '300 Baud - 7E1',0 RET OK4E: CPI BR4E JNZ OK4F CALL JMP$ILPRT DB '1200 Baud - 8N1',0 RET OK4F: CALL JMP$ILPRT DB '300 Baud - 8N1',0 RET ; ; ; (END OF INITMOD AND SETUP ROUTINES) ;======================================================================= ; ; The following routine can be used as an auxiliary menu for notes of ; interest to a particular computer, etc. If using the Hayes Smartmodem ; this is unavailable without a spcial address change. ; SPCLMENU: RET ; ;----------------------------------------------------------------------- ; ; ; NOTE: MUST TERMINATE PRIOR TO 0400H (with Smartmodem) ; 0C00H (without Smartmodem) ; END ;